How to Change a Subaru Spare Key

If you lose your subaru locked keys in car car key, call a locksmith. Locksmiths will usually cut you a key for less than the dealer.

Fob remote "push to start" intelligent keys or a plain metal key are the two most common types of Subaru car keys. The Fob key is equipped with an embedded chip that it will require reprogramming.

Keyless Entry System

A key fob lets you to lock or unlock your Subaru from a distance and can even unlock the trunk or lift gate of your vehicle. These remotes make use of keys in your car to connect to your vehicle's computer.

Certain models of subaru key replacement offer a little-known feature called PIN Code Access. This lets you use a personalized number sequence to start and open your vehicle. If you have a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that has this feature, make sure you check your owner's guide to find out how much does a subaru key fob cost to use it.

If your locked keys in subaru forester stop working, there's an excellent possibility that the battery in the key fob is dying. You can test the battery life of your key fob using an electronic tester that you can carry around or a multimeter in your garage.

The next step is to remove the key fob from its case and examine the circuit board that controls the transmitter. It will have one or two sets of 8-digit numbers, so write down the first set so that you are able to recall it later. After you've done this, you can begin programming the key fob at home. This procedure is different based on the year and model of your vehicle. However, it's usually easy enough to do yourself.

Key Fobs

Subaru's newest models feature key fobs that can not only unlock doors, but also turn on lights, lock gas cap and even start the car. This last feature is particularly useful if you've ever parked at the gas pump only to find that your car isn't starting because the key fob battery failed.

It is likely that your Subaru's key fob, regardless of whether it's old or new it is able to be replaced. It's important to keep in mind that newer models with the highest level of technological advancement may require a trip to the dealership. With little effort and some time, you can create your own replacement key fob.

Start by opening the case and inspecting the circuit board of the transmitter. (Instructions on opening the case are usually found in the owner's manual). There should be one or two serial numbers with 8 numbers each. Keep the first series of numbers on hand for future for reference.

Then, sit in the driver's seat, and close the doors. Turn the key to start your car and then switch off after ten turns. Press the lock button on your key fob and then open the door to verify whether your doors function properly. Close the door, and then take the key off. You should hear your vehicle chime again, indicating that the key fob is programmed.

Ignition System

If your Subaru keys aren't functioning as they should it could be due to the fact that the battery is dead. If you have the knowledge, you can change the battery on your key fob yourself. The replacement battery isn't expensive and fairly easy to find. If your key fob won't respond to your commands, it could be another problem. To find a spare key, it's advisable to go to a dealer. They'll ensure that the key is a genuine Subaru key that's under warranty. They'll also program it to your vehicle. This is a lot simpler and safer than purchasing an aftermarket one from a website.

You can also have the dealer cut a new key if you supply them with your VIN and proof of ownership. They'll use this information to code the new key in order to be accepted by your immobilizer. This is a more intricate procedure than cutting a single key, and the dealer will charge you more for it.

Once the new key has been programmed then you'll be able change it over to your existing key. It will take only five seconds to insert the new key, so keep your working key close at fingertips. You can take the key off once the security light has stopped flashing and test it.

Battery Replacement

Subaru fobs are very useful since they can turn on the sunroof and power windows of your vehicle with just one button press. The battery inside your Subaru fob isn't designed to last forever, and it will have to be replaced eventually. This short guide from Capitol Subaru will help you to replace the battery yourself.

To begin the process, you'll have to find the small crevice in the seam that divides the back and front of your key fob. You can cut this seam using an flat-head screwdriver to expose the small compartment that contains the battery. Insert the new battery and make sure it is facing the right way. Remove the old one. After you've put everything together you can use the new key fob for locking the vehicle, unlocking it, and then starting your vehicle.

It's always an excellent idea to keep an extra set of keys on hand in case you've lost them or they're not functioning properly. A new key can be found at your local dealership for cars or you can get one made by the locksmith. Either way, it's important to get your key fob functioning properly as soon as you can to allow you to drive safely!