Reasons Your fiat key cover 500 Key Fob Won't Work

A key fob with the fiat panda key fob 500 number is a great way to unlock the doors and start the car. There are many reasons why the key fob might stop working. It could be due to a dead battery, damage to the receiver module, water issues, and interference.

This listing is for a NEW replacement fiat remote key Flip Key Remote - an exact replica of the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Key fobs of today have limited operating range and must be within a few inches of your vehicle to work. If you're far from your vehicle, and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery in the coin cell (Part number CR2032) with a fresh one from a trusted brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store, or online.

After you've replaced the battery of your coin cell You can test it by standing close to your Fiat 500 and pressing the buttons. The car should flash its parking lights, and the key fob will operate the lock and unlock switches.

If the key fob doesn't work after replacing the battery, it may have water damage that prevents it from connecting to the receiver module in your car. Water damage can happen in many ways, including the simple splash or submerging the key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, try placing it in a dry rice bag to pull the moisture back out. If this doesn't work, your fob may need to be reset by an experienced auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and eventually die. It's not a good idea to let the fob get wet but don't give up if you accidentally drop it in water, or fail to take it out of your pants pocket.

First remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob afterward to see if it is working. If the key isn't working then it might need to be changed. This is usually done by an auto locksmith or dealer.

If the key is a newer model and has not been programmed to your vehicle it is likely to need to be replaced completely. This is a straightforward process that can be completed by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your vehicle. They will also need to reprogram the fob for the system of your car. This is a low-cost and quick process that could be completed the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote usually has an area of 30 feet or less and if it's far from your vehicle, it won't respond to your commands. It is possible to solve this problem by moving the remote closer to your car until it responds.

If your fob doesn't work after replacing the battery in the coin, also known as a "button", "watch" or "button" it could be due to a problem with the internal circuit board. In most cases, reprogramming the fob can resolve the issue. You can find instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries locked keys in car boot fiat punto their place. If they lose tension, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob could be out of connection with your vehicle as a result of hardware or software problems. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases, they may need to install the software again in your body control module as well.

Interference

Interference can also cause the key fob not to receive or transmit a signal. This may happen if the keyfob is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons why the key fob might not function could be due to a weak connection to the buttons or the internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. battery replacement, reprogramming and using the Spare Fiat 500 Key key fob, you could have a faulty receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then processed by the vehicle.

Luckily, there is an easy method of resetting all on-board systems in your 500 device, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then, reconnect the battery. This will clear out any residual electricity and restart the car's computers. This can help the key fob to function again. If the issue continues, you should speak with an expert technician. They can determine the exact cause of your issue.