How to Fix a Dead Kia Picanto Key Fob

The Kia Picanto was built for the city. It swerves through traffic voids that larger vehicles can't, and navigates width limits as if they're not there at all. Despite its shabby appearance it's loaded with plenty of features.

There are many reasons that the key fob in your kia Picanto may not function. A dead battery is the most typical cause.

Dead Coin Battery

A dead battery is the most common cause of a kia cerato key replacement Picanto's key fob not working. Usually the key fob will display warning signs before it dies in a way, like losing the range or showing irregular behavior. It is best to replace your battery in the event that you notice any of these symptoms before the battery completely fails. Make sure you choose an alternative battery that has identical in size, voltage and specification as the original one.

If the key fob does not work, it might be an appropriate time to go to a dealer for a replacement. Only then can you be sure that the new key fob is compatible with your vehicle and properly programmed. If you try to program the key fob improperly the internal chip could be damaged and it will stop working.

A receiver module that has acquired a fault is another possibility. This could be due to a damaged chip or simply wear and tear as time passes. Symptoms of this problem can be difficult to recognize but it's important to determine the cause as soon as you can. If you are unable to use your key fob to lock or unlock the doors, or even if the spare isn't working, it is time to contact a dealership or service center to get help. They will be able diagnose the problem and fix it.

Faulty Chip

The key fob is equipped with a chip inside it that sends signals to the car's computer. If the chip is damaged and cannot transmit the correct code, and the immobilizer feature of the car will be activated. This could be due various reasons. One reason is a low battery in the key fob. Water damage is another possibility. If the fob becomes wet, it is very likely that it will cease to function.

A malfunctioning chip could be the reason for a Picanto fob won't turn on the engine. If you've replaced the battery, reprogrammed it and then inserted the fob but it still doesn't work, the circuit board could be damaged. You'll need to replace the circuit board in the event of this.

To open the Fob you must press a button that is located on the back of the fob. Once this is done, you'll be able to remove the mechanical key. The video below will demonstrate how to replace the battery in the key fob. Use a battery with the same dimensions and voltage. The Fob can be damaged if you use the wrong type of battery. After replacing the battery, you must test it by pressing the lock button. If it works, you are using a quality Fob.

Faulty Receiver Module

The key fob you have is subjected to quite a beating and isn't a perfect piece of equipment. As time passes, its contacts with batteries and buttons may be damaged and stop functioning properly. Fortunately, it's quite simple to repair this yourself with a few simple tools.

To work, the fob has to transmit a signal to a receiver inside your car. If this module is damaged it will not be able to open or start your vehicle. There are a variety of possible causes for this issue however the first thing to do is reset the fob.

This is done by disconnecting the cable and letting the 12 volts battery drain completely. Then, reconnect the negative and positive cables in reverse order.

If the battery is in good health and the fob does not have any water damage, the problem may be with the signal. This could be caused by a variety of things including interference from nearby transmitters or objects using the same frequency band as your Picanto's receiver.

Key fobs are constructed with rubber seals in order to protect the electronic chip from getting wet, but if they're submerged in water for prolonged periods the chips may be destroyed. It's crucial to keep your key fob out of water and only use key fobs with waterproof designs.

Poor programming

A 2011 kia soul key fob programming (find out this here) Picanto key fob is an efficient way to unlock and start your vehicle. You can also use it to control the features of your car. It is crucial to understand how to make use of the key fob effectively especially when driving in harsh weather conditions or if you have a limited mobility. There are a number of Kia Picanto keys locked in kia soul tricks that can aid you.

If your key fob suddenly stopped working, it could be a problem with the internal chip. It is rare but it could happen. To determine the cause you should talk to an kia rio locked keys in car dealer.

You can also reset the Picanto keyfob. The process is relatively simple and can be done at home. The first step involves removing the key fob. Then connect the diagnostic tool to the OBDII port that is located beneath the dash and then turn on the engine. The diagnostic tool will then seek out information regarding your Picanto. This includes the VIN, the make, and model.

You can also look for dead batteries. The retaining clips made of metal inside the key fob are designed to hold the battery in place and complete the circuit. If the retaining clip is damaged, it can disrupt the flow of electricity causing an interruption in the function.