How to repair Car key Car Keys

Car keys might seem tiny and insignificant, however they are essential for the proper operation of your vehicle. Replacing a traditional or a transponder one could cost as much as $200.

However, there are ways to fix your car keys at home for only a fraction of the cost. This article will address the most frequent car keys issues and their DIY fixes.

Dead Key Fob Battery

Cars are equipped with remote key fobs that makes opening the doors, trunk and tailgate easier than ever before. However, the battery inside the device could die. There are some tricks you can employ to fix this issue quickly.

Check to see if the car is still in the ignition mode. If it is, the battery on the key fob could be drained instead of dead. To test this, press the button on the fob against the ignition button on the vehicle. If this is successful, the battery is likely fine and needs to be changed.

To replace the battery inside the fob, open the case with an screwdriver. Do not apply too much force as this may cause the fob's casing to split. If the fob isn't coming open easily, try wedge your pry tool into multiple places on the outside of the case.

Open the electronic portion of your vehicle after you have removed the mechanical key. Then, you can insert the replacement battery and then snap the shell back together. If the key fob doesn't work after this, there may be a bigger problem with your car's remote start system that requires a professional to diagnose. A reputable mechanic will be capable of helping you in this situation. You can also call roadside assistance to assist with your vehicle if needed.

Broken Key Ring

If your key fob isn't working because the ring is broken there are a few options you might try. Examine if you can find the broken piece inside the ignition. If it's still inside, remove it without damaging either the ignition lock or the door lock. Call a locksmith if you are having difficulty removing the key repairs near me. They have tools that can safely remove a damaged key from the ignition.

Another common cause of a broken car key is the corrosion of the circuit board or frame. You can clean the circuit board using the help of rubbing alcohol and a cotton swab. This will eliminate the corrosion and prevent damage to the contact pads.

You can fix a broken ring using a strong wire or nail to close the hole. Superglue can be used to repair the broken key ring. First, clean the damaged ring with a damp cloth and then apply a small amount of superglue on each end of the wire or nail. Then, press the pieces together and allow them to dry before using your vehicle. These DIY solutions may look appealing, but they're just a stopgap measure. It's best to hire an skilled locksmith for any long-term repairs. They have the tools and expertise to repair a damaged car key quickly and efficiently. They can even replace the battery inside your key fob, and modify it if necessary.

Broken Key Blade

Some key blades break from a lot of wear and tear. If this happens, it's probably time to buy a new key. This problem isn't nearly as serious as you think at first. The primary issue is that the blade snapped off the case.

Spraying lubricant into the keyhole is one method to fix it. Then, you can employ pliers or tweezers grasp the damaged end of the key and pull it. If the key is magnetic, you could also try using a magnetic tool to help pull it out. Use a magnet to help you remove the key, but be cautious to not sever the lock tumbler.

Call a locksmith immediately if you are unable to take out the damaged part of the key. They're equipped with special tools to safely extract keys without causing further damage.

You can also apply super glue to repair car key a snapped key. Apply a small amount of glue to the edges of the crack and press them together. Make sure the glue has dried before inserting the key into the lock. But this method isn't very secure and you may need to repeat the process a few times before it's successful. Super glue might not be able to hold the key in place. This is more of a temporary fix than an option that is permanent.

Broken Plastic Loop

If your key fob's plastic loop is damaged it could render the key ineffective. It's an simple fix. For a replacement alternative, you can opt for a thick wire or finishing nail. For each end of the nail or wire you need to drill two holes into the loop of plastic. Cut the wire or nail into a key width, then place a small drop of superglue into each hole. Apply the nail or wire into the holes and allow them to dry.

Another option is to get a replacement shell from a locksmith that sells them. They can transfer the programmable part of your key into the new shell, and cut new blades for less than the cost.

It's not the best solution, but it will bring you back on the road if your key broke in half. However, it can be difficult to repair the key blade if it's in the ignition. You could try using hair clips or needle extractor tool to remove the damaged part out of the ignition, however this is risky if you're not cautious. The best choice is to contact an expert locksmith who has tools to safely remove broken keys from the ignition. You can also request a new key that is made using appropriate cuts for the ignition of your car key repair cost.

Broken Master Key

If a key is broken inside the lock, you'll have to attempt to retrieve it before it's completely destroyed. There are a few techniques you can employ, such as using lubricants and tools like needle nose pliers or tweezers to pick up a piece of the damaged key and pull it out.

Spray the inside of your lock with WD-40 or a graphite powder. You may also try the hacksaw method, which involves carefully sliding the blade down along the edge of the broken key, and connecting to a few of the 'teeth'. If you succeed in doing this you will be able to take the broken key from the lock.

Many hardware stores carry the spiral key extraction tool. It's a thin and flexible bar with spiral threads, that can be inserted into the keyway and bent to dig into the damaged section of the key. Once it has been snagged onto the serrations, you can turn it in a circular direction and press it against the broken part of the key to pull it out.

Before contacting a locksmith try to remove the broken master key. If you're not able to take the broken piece off, you'll need to call in the professionals. A locksmith can make you an entirely new key that will be programmed using your car transponder.