Choosing Upvc Window Replacement Hinges

Choosing and fitting upvc window replacement hinges isn't as complicated as you think. It is essential to verify that the arrows on the hinges are facing in the correct direction and also the thickness (13mm or 17mm) of the hinge arm on the open frame.

There are a variety of different kinds of aluminium doors hinges, each having their distinctive characteristics. This article will discuss the most popular types of uPVC window hinges and the advantages they offer.

Egress/Easy Clean Hinge

They are a great choice to replace or upgrade a fire escape safety window since they open at a full 90-degree angle. They can be closed to an easy-clean position that allows you to see the windows' exterior without the need to climb ladders or lean at risky angles.

Yale is one of the most trusted and well-known brands in the home security industry. These hinges are compatible with any type of uPVC side-hung windows. They can be moved into the clean position by pressing in a small button and then sliding the window sash to one side. When the sash is closed, it will be reset to its original position.

They are available in 13mm and 17mm stack heights. Based on the size of your window we recommend using our Egress Selection Guide to determine which one is the best fit for your needs.

These hinges are designed to be used with standard side-hung frames which is made of aluminum or uPVC. The friction screw is used to adjust the resistance. This makes opening the windows easier and reduces the chances of a mistaken closing in severe winds. They have been tested for more than 30000 cycles and are in compliance with British Standards approved BS EN 130126-6:2008 and BBA/Secured by Design.

With no buttons or catches There are no buttons or catches. Nico Egress Easy Clean Friction Hinge is simple to use and provides a convenient solution to emergency egress as well as safe cleaning. Firstly, open the window to the egress (full opening) position, then press the hinge retaining clip on the inside of the bottom corner. This will release both the catches on the top and bottom and allow you to move the sash towards the easy-cleaning position. Once it is in the easy-clean position close the window to reset the hinges to their egress positions.

Fire-Escape Hinge

Fire Escape Hinges commonly referred to as "Easy Clean" hinges are used to replace side-opening windows for egress (fire safety) reasons. These types of hinges open wider and faster than normal hinges, allowing a large clear opening to escape in the case of a fire. Building regulations require that this kind of hinge has to be set in any habitable space with windows.

They have an exclusive friction stopper that allows the window to open at a 90 degree angle and also allows the sash opening to slide across when it is open for easy cleaning of the external side of the glass, without having to use ladders. The hinges are easy to operate and do not have complicated buttons or catch mechanisms. They can be operated from inside of the house using an easy, safe lever.

The hinges are made in the UK by Cotswold and come with a child safety restrictor for day to day use which can be turned off by a hidden button, providing you with peace of mind that your children won't accidentally open the window too far. The stack heights are 13mm or 17mm.

Measure the length of the current side-hung window hinge that is fixed to the frame. (See the guide on measuring upvc window hinges). Choose the right size hinge below.

Be aware that the measurement is taken from the part that is fixed to the frame and not the sash. The real hinge length may be slightly longer or shorter depending on the manufacture of your old windows. Also, when choosing the width of your hinge the majority of upvc windows can be fitted with a 13mm stack height but should your window frame has 17mm, then select the option to use this. Alternately, you can install the 4mm packer to make up the difference. All double glazing hinges are in two different directions (1 left and one right). The hinges are not equipped with screws. If needed, they can be purchased separately. Our upvc window repair screws are recommended. They are specifically made to improve the performance of your hinges that allow them to run efficiently for a longer. They have a lower friction design and an improved weather seal with a new nylon reducer cap.

Restricted Hinge

There are times when windows must open fully and this can be difficult using the standard hinge. These child safety friction hinges are an excellent way to solve this problem. They can be used when ventilation is required but escaping or cleaning a fire is not possible. They function by limiting the amount that the sash can open and allowing the to override this restriction by pressing a button. They can be used for side and top-hung windows and are available in 17mm and 13mm stack heights.

The Nico Restricted Egress Friction Hinges combine the advantages of a standard restrictor and a pivot for fire escape to provide a simple and effective way to comply with building regulations. It is suitable for side-hung and top opening uPVC windows and is available in 17mm and 13mm stack heights. It is available in a pair that has one hinge which is the one that is restricted for egress, and the other the unrestricted. This permits one hinge to be installed at the bottom and the other is set on top.

These uPVC hinges are restrictive and have been tested to BS6375 part 2 and are designed to be used on windows that cannot be opened fully such as a small children's bedroom. The mechanism limits the amount the sash is able to open to the safety level of 100mm and re-engages once the window is closed.

Like the other kinds of uPVC friction hinges, these can be used on any type of window and are ideal for those difficult to access windows above the ground three-storey flats and windows that normally require a ladder for access to them. They can be paired with our range of security enhancements such as hinge guard protection plates or dog bolts to offer PAS 24 performance.

It is essential to measure the hinge on your current window hinge repairs near me to ensure that you get replacements of the same size. The easiest method to do this is to look at the hinge in the image gallery and determining the best place for it to be placed. The hinges that hang from the top can only be positioned on one side, while the side hung ones can only be placed on one side.

Standard Hinge

A standard hinge has metal-to-metal contact and no extra parts to decrease friction. It's available in a range of finishes and fire-rated. For a quick way to determine the radius of your hinge, lay it flat and line up a dime and quarter in two corners. If the quarter is more snug, then the corner should be turned to 5/8 inches.

The right hinge can make or break the look of your door. Achieving the same design and style of your hinges with your door will create an attractive and well-integrated appearance.