How to Change a Subaru Spare Key

If you lose your Subaru car key, contact a locksmith. Usually, they can cut new keys for you cheaper than the dealer.

Fob remote "push to start" intelligent keys or a plain metal key are the two main types of Subaru car keys. The Fob keys have an embedded chip that it will require reprogramming.

Keyless Entry System

A key fob can be used to lock or unlock your Subaru from a distance. You can even open the trunk or lift gate of your vehicle. These remotes make use of keys in your car to communicate with your vehicle's computer.

Subaru models come with a lesser known feature called PIN Code Access. You can utilize a personalized number sequence to start and unlock your vehicle. Read the owner's manual to learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's possible that the battery inside the key fob has gone out. You can test the battery life of your key fob using the portable tester or multimeter that you have in your garage.

Next, you'll want to remove the key fob from its case and inspect its circuit board for the transmitter. You'll be able to see two or three sets of 8-digits. Write down the first one so you can remember it. Once you've finished you can put the key fob back together and you'll be ready to begin programming it at home. This procedure differs based on the year and model of your vehicle. However, it is usually simple enough to complete yourself.

Key Fobs

subaru chip key replacement's newest models feature key fobs which not only unlock doors but also turn on lights, lock the gas cap, and even start the car. This last trick is particularly helpful if you've been at the gas station only to discover that your car isn't starting because the battery for the key fob failed.

It doesn't matter if your Subaru is brand new or old it's likely that the key fob can be replaced with little difficulty. Remember that some of the modern models, with the latest technology, might require visiting a dealer. With just a bit of effort and time, you can build your own key fob replacement.

Begin by looking at the circuit board of the transmitter in your key fob (instructions for opening the case should be provided in your owner's manual). There should be one or two serial numbers that have 8 digits each. Write down the first number series and keep it in your wallet for reference in the future.

After that, get in your driver's seat, and close all doors. Turn the key to start your vehicle before turning off after ten turns. Press the lock button on your key fob and open the door to verify whether your doors function properly. Close the door, then take the key off. The chime should be heard from your vehicle once more, signalling that the key fob has been programmed.

Ignition System

If your Subaru keys aren't functioning as they should it could be because the key battery is dead. If you know how, you could replace the battery of your key fob yourself. A replacement battery is inexpensive and easy to locate. If the key fob you have doesn't respond to your commands, there could be a different issue. It's best to go to a dealer to obtain a spare key. They'll ensure that the key is genuine Subaru key, which is covered under warranty, and that it is programmed to your vehicle. This is much more secure and less expensive than purchasing an aftermarket key from a business online.

The dealer will also cut keys for you, provided you provide them with your VIN number and as evidence of ownership. They'll use this information to program the new key in order to be accepted by the immobilizer. This is more complex than simply cutting a key, and dealers will typically charge more for this service.

Once the new key is programmed it will be able to change it over to your existing key. It will only take you five seconds to insert the new key, so make sure to keep your working key close to your side. You can take the key off when the security light has stopped flashing and test it.

Battery Replacement

One of the key advantages that make subaru impreza key fob fobs so useful is their ability to turn on your car's power windows as well as sunroof with just a press of a button. However, the battery that is in the Subaru key fob isn't made to last forever and will eventually need to be replaced. This quick guide from Capitol Subaru will help you to replace the battery on your own.

To begin you'll need to locate the small crevice in the seam that divides the front and back of your key fob. Utilizing a small flathead screwdriver, you'll be able to pop the seam to reveal a small area inside which is the battery. Install the new battery and make sure it's facing in the correct direction. Remove the old one. Once everything is put together and in place, you can use your new key fob to lock, unlock, and start your vehicle easily!

You should always have a spare set of locked keys in subaru forester, especially if yours is broken or has been lost subaru keys. You can buy a new key from your local dealership or get it cut by locksmiths. It is important to ensure that your key fob functions correctly as soon as you can so you can drive safely.