Replacing uPVC Window Handles

Changing upvc window handles is a simple task. The important thing is to ensure that the replacement handle fits the spindle that was cut out of the window mechanism.

If you follow the steps below the handle of any cockspur will fit on most windows. The height of the step of the handle is crucial.

What to Do You Look For?

Many of the windows in the UK are fitted with uPVC handles and, over time, they may begin to show signs of wear and tear. If this occurs, the handle can become loose or difficult to operate, which makes it essential to replace it. This is a fairly simple task that is achievable by anyone who is comfortable using basic hand tools.

The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to locate the fixing screws or pins that hold the handle in position. They are usually located on the inside face of the handle. They can be removed using a screwdriver or pliers.

When the handle is loose and sagging, gently pull it back from its hinges. It is then time to locate a replacement handle of the same style and size. This can be done online or in the local DIY store and should take five minutes using the help of a screwdriver.

When replacing the handle on a uPVC handle It is crucial to consider the step height. This is the distance from the base of the handle until it is placed on the frame of the window. This is a typical measurement, and you should verify the step height before ordering a replacement handle.

Depending on the type of handle you are using, there are different sizes that are available. Inline handles are offered for uPVC windows that have centers of 31mm for lugs, while cockspur handles come with centers of lugs of 43 millimetres. Tilt and turn handles are typically found on uPVC windows, and they feature a specific design that allows windows to be tilted for ventilation and turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack inside instead of breaking away from the base section. This can make them hard to open and therefore it is important to make sure that any replacement handle you purchase has the same length of spindle as your existing one.

Take off the handle from the Old Aluminium Window Handles one.

If your window handles are damaged or not properly fitted, they could cause double-glazed windows to open and close incorrectly. They could even become stuck. This could be due to many factors, including general wear and tear on the handle or corrosion. In these instances it is essential to replace the upvc window handle as quickly as you can in order to prevent further damage or loss of functionality.

When replacing upvc windows handles and handles, it is important to remove the old handles from the window handle repair. Begin by removing the screw covered when the handle in closed position. This will reveal a screw and once removed, you are able to begin to remove the handle. It is possible to make the task easier by using an electric screwdriver.

You should also be aware that screws could be hidden in plastic caps. It is recommended to remove the covers with a Stanley knife. After removing the handle, you'll need to check the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is important to measure the spindle length on the handle you used to replace it with and compare it to the size of the window mechanism spindle cutout.

The various types of upvc window bi-fold doors handles are: Espag handles, which are equipped with a central screw and can be turned left or right; Cranked handles which have two screws and are found on tilt and turn windows made of upvc as well as Spade handles, which have an arm with a flat surface and can be used on either side of the window handle upvc. It is easy to replace the handle when you've identified one that is suitable. Simply put it in place and make sure the spindle is properly inserted in the lock mechanism. Once you have done this, tighten the handle to the window frame. Your replacement upvc handles should now be secure.

Take a measurement of the Spindle

If you have to replace a upvc handle that has collapsed, it's likely the spindle holding it in place is damaged or loose. In some instances, this could be fixed with a screw or pin to secure it. In other instances, it may require replacement completely. There are a few different types of upvc window handles. They include espagnolette handles that are inline or cockspur handles. They also have tilt and turn handles. Each type has a different method for installing and removing the handle.

It is crucial to measure the current handle before buying an alternative. This will ensure that the handle fits the window correctly and will be the right size. Luckily, all handles conform to industry standard sizing so it's quite easy to locate the right size.

To determine the size of the handle, turn the window to the open position. You will then be able to see the size of the screw or pin that is holding it. Then take the ruler or tape measure to determine the length of the spindle. Once you know the length of your spindle, it is possible to buy a replacement of exactly the same length.

When you are looking to replace a handle you should be aware of the step height of an window handle made of upvc. The step height is the distance from the base of the handle to where it rests on the frame. Typically, this will be about 21mm for uPVC windows, and 9mm for aluminium. Dropping objects into the gap will let you determine how far the handle extends before it comes into contact with an obstruction.

Cockspur handles usually have different backset heights based on the style of window handles for wooden windows they're installed in. Inline Espag handles come with a standard height of 43mm from centre to centre (2 fixing points). Cockspur handles, however they have different backsets according to the shape of the window they are in. This is due to the fact that they have an extension spur that extends from the handle and is secured over a cockspur wedge striker plate.

Fit the New Handle

After you've chosen the new handle, ensure that it is aligned with the holes for screws on the door. Then secure it using the screws provided. Install the latch lever the same manner as the handle that you are replacing in the event that you are replacing the door handle. Finally, reattach the door trim in order to conceal the mounting screws and finish off your project.

Tips: To remove the metal head from the wedge of wood make sure the handle is held so that its wider end is resting on the floor and use an hammer to tap the thin end of the handle. Be careful not damage the handle or spindle.