Reasons Your fiat car keys cut 500 key cutting (pop over to this site) 500 Key Fob Won't Work

A fiat 500 key fob is a handy way to unlock the doors and get started the car. There are a myriad of reasons the fob may stop working. These include a dead battery, damage to the receiver module, water issues, and interfering.

This listing is for an NEW replacement fiat ducato key Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs have a very limited operating range and should be within only a few feet from the vehicle to operate. If you're far away from your vehicle when you press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery on your coin cell (Part number CR2032) by a new one from a trusted brand such as Panasonic, Duracell, or Energizer. You can find them in the local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing close to your fiat key replacement cost 500. The parking lights should blink and the key fob will operate the lock and unlock switch.

If the fob's key doesn't function after replacing the battery, it could have water damage that stops it from connecting to the receiver module in your vehicle. Water damage can happen in a variety of ways, such as an easy splash or submerging the key fob into saltwater at the beach. If you believe your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work your fob is likely to require reprogramming by an experienced locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean, or wash it in a washer. Saltwater can cause the circuit board to become shorted and eventually cease to function. It's not good to soak the fob in water, but don't give it up in the event that you accidentally drop it in water or fail to take it out of your pocket.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Next check the fob to verify if it is working. If the key doesn't function it could need to be reset. This is usually handled by an auto locksmith or dealer.

If your key is older and not programmed for your car You will need to replace it completely. A professional automotive locksmith will be able to complete this process. The locksmith will need the key cut to match your car's ignition. The locksmith will also have to program your fob into the car's system. It's a simple and cost-effective procedure that is usually completed in the next day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote has a range of 30 feet, so if you are too far from your car it will not respond to your commands. You can solve this issue by moving the remote closer to your car until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. Reprogramming the fob typically resolves this problem. You can find the instructions on how to do this for most automobiles by searching YouTube or looking through the owner's manual.

It could be necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension it can prevent the coin battery from being properly seated, and this will cause your remote to malfunction.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software problems or hardware issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances the software might require reinstallation in your body control modules.

Interference

In addition to a dead coin battery The key fob may not be able to transmit or receive signals due to interference. This could occur if the key fob is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob could not work due to a poor connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming or using a spare key fob. The receiver module, which is located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting all of the onboard systems in your 500 and include the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity and then restart the car's computer system, which can help you get your key fob working again. If the problem persists it is recommended that you consult a certified technician. They will be able to determine the exact cause of your issues.