UPVC Replacement Door Handles

Over time, the handles on your doors will wear down and need to be changed. When replacing them, it is essential that the new handles conform to the exact dimensions of the old handle.

The top screw's position, the lever and the keyhole dimensions are the three measurements you need to check. Refer to the size guide for assistance with this.

Inline Lever/Lever

A lever or lever door handle is a contemporary handle that can be installed on new or replacement doors. This kind of handle is available in a variety of designs and finishes. A number of manufacturers make this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles of uPVC/Composite are made of sturdy materials and are ideal for multi point sash lock door handles doors which require a robust design. The handles are inline and work with the same spindle as well as screw fixings. They can be easily incorporated into existing or new uPVC/Composite doors.

The sprung lever design allows the handle to be positioned and angled for comfortable operation and is suitable for all users. The handle has been endurance tested to 200,000 cycles, which helps to ensure the quality of the finish and performance of the handle over time. The sprung lever is also adjustable to accommodate a wide range of locks. This is useful for narrower doors where the cylinder is further away from the door. A lever that is shorter is a good choice for doors where the latch could be activated by the thumb turn on the inside.

Lever Pad

The lever pad upvc handle differs from the lever handles used on the majority of doors. These handles are operated by one spindle, or two spindles, inline or offset. They are usually utilized on UPVC doors with double glazing. They are available in a variety of finishes and variations.

The handles have been tested to the minimum of 200k cycles and are available in several finishes like White, Silver, Chrome & Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This gives the handle an outstanding performance and durability to serve its intended purpose.

All UPVC lever pads for handles include a spindle and screws and can be mounted on a uPVC door. The backplate fixing centers of 211mm allow for a wider size of handle which can be beneficial in replacing a defective or worn multi point door lock mechanism. These handle levers have springs, which eliminate the problem of handles for doors that slide out of their horizontal position when not in use.

When selecting the replacement upvc door handles replacement handle and spindle, it is crucial to match the dimensions of the PZ of the multipoint lock as well as the uPVC door. This measurement is also referred to as 'handle centres or cylinder centres'. It is important for matching the correct handles.

Once you have the correct PZ size, you'll need to ensure that the handle lever pads and push pads are a appropriate shape to accommodate the American with Disabilities Act (ADA) compliant handles that you require for your doors. These are typically of a round or square shape, with an internal lever and external push pad.

Most of the UPVC lever pads we sell are sprung, meaning that they will return to their horizontal position when they are not in use, instead of hanging out and possibly securing in the frame. This keeps draughts out of the property. You will also find that the majority of UPVC handle lever pad style handles are swivel which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are typically found on uPVC doors, but can also be used on other types of doors. They work with a key to unlock a cylinder that is then revealed with pins that can be aligned to those in the lock body and permitting them to turn an revolving cam, opening the door. Euro cylinders can be equipped with up to six pins, with internal and external doors usually requiring different levels of security.

The choice of the correct cylinder is crucial; it depends on how your door and handle are utilized. External doors, for example should be equipped with cylinders that are more secure while internal doors can be secured using the standard cylinder. Certain cylinders are equipped with additional features that can increase security, for instance, anti drill or anti bump properties.

To ensure that the euro cylinder is the correct size for your door, it must be measured correctly. The cylinder must be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn, in the event that one is present. If you cannot measure with the lock in position, you can take it out of it. A cylinder that is protruding beyond the handle and escutcheon might be vulnerable to attacks, such as snapping locks, so it is crucial that it's not too long.

The design of most newer cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease attack chances by forcing the cylinders to turn in a new direction. This can help deflect the attack, and ensure your door is secure.

Certain cylinders are made to resist snapping. This is an increasingly common method of attack on cylinders, which is where the break line of the lock is smashed by a tool that is specially designed to snap off the front of the cylinder and allow the door to open. This is much quicker and less difficult than gaining access through multipoint locks and leaves little evidence of a break-in which can impede an insurance claim.

Spring Cassette

This spring cassette sits within the base of the door handle backplate providing a sprung solution and returning your multipoint lock handles to their normal position after use. The handles had no spring and would drop when the locking mechanism was disengaged. This simple part is the best solution to fix this problem. It also stops your door from becoming stuck in the closed or open position since they aren't easy to close manually.

These spring cassettes are specially made for use with multipoint locks that are sprung They will not work with unsprung multipoint handles and you will require a hole specifically cut in your backplate to allow these to fit (please look at the image for a technical diagram). These cassettes can be used as a replacement to broken or missing cassettes that are in the backplate of uPVC door handles. They feature a square cut out which allows for an 8mm spindle to be used and are available in a variety of.

These spring cassettes are a great value-for-money solution to the issue of door handles that are sliding. These spring cassettes are simple to install and will increase the lifespan of your uPVC door. Please contact our team for more information about our wide range of uPVC accessories and spares. We are available to help and happy to provide professional advice.