Reasons Your fiat panda key replacement 500 Key Fob Won't Work

A fiat spare key 500 key fob makes it simple to open doors and start your vehicle. However, there are numerous reasons the fob could stop functioning. This includes a dead coin-battery, water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob that isn't working. Modern key fobs operate with a restricted operating range, and must be within some feet of the vehicle to function. If you are further away from your car and hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the coin cell battery (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. You can usually find them at your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you are standing close to your fiat key replacement cost 500. The parking lights should flash and the key fob will operate the lock and unlock switch.

If the fob's key doesn't work after replacing the battery, it could have water damage that stops it from connecting to the receiver module in your vehicle. Water damage can happen in a variety of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture back out. If this does not work, you'll need to have the fob replaced by an auto locksmith or a dealer.

Water Damage

While the fob comes with rubber seals to keep water out of the chip's electronic circuit, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob's circuit board that can cause it to short out and eventually end up dying. The fob getting wet is not an ideal idea but if you accidentally drop it into a cup of water or don't remember to take it out of your pants pocket before running the washer, don't give up hope.

First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob to see if it is functioning. If the fob doesn't work, it might need to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is older and is not programmed for your vehicle, you will need to replace it completely. A professional locksmith for automotive will be able to complete this process. The locksmith needs to cut the key to match the ignition on your vehicle. They'll also need to reprogram the fob for your car's system. This is a simple and affordable process that is usually completed the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote has a maximum range of 30 feet, which means when you're too far from your car it will not respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board issue. Reprogramming the fob typically resolves this problem. You can find directions on how to do this for all automobiles by searching YouTube or looking through the owner's manual.

It's possible that you need to replace the metal retaining clips that keep the coin battery. If they lose tension, they could stop the coin battery from being properly seated, and this will cause your remote to malfunction.

In rare instances, the fob could be out of connection with your vehicle as a result of hardware or software issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances the software may require reinstallation in your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This could occur if the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons why the key fob could not function include a poor connection to the buttons or the internal chip or water damage.

If the key fob been unable to function for a while suddenly, or after trying everything you can do at home to resolve it e.g. battery replacement, reprogramming and using the spare key fob, you might have a defective receiver module on your 500. The receiver module, which is located under the dashboard, detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will remove any remaining electricity and restart the car's computers, which could allow you to the key fob to function again. If the issue continues you should seek out an expert certified technician. They can identify the root of any problems.