How to Repair Car Keys

Car keys may seem tiny and insignificant, however they are vital to the operation of your vehicle. The cost of replacing an old or modern transponder car key can be upwards to $200.

There are methods to fix your car keys at home with only a fraction of the cost. This article will discuss some of the most frequent car key problems and their DIY solutions.

Dead Key Fob Batteries

The remote key fob repair near me key fobs for keys that come with cars make it simpler than ever before to open the trunk, doors and tailgate. However, the battery inside the device can fail. There are a few tricks you can use to resolve this issue fast.

First, check if the car is still in ignition mode. If it is, then the battery on the key fob could simply be depleted instead of dead. To test this, press the button on the key fob straight up against the vehicle's ignition button. If this does not work, the battery is probably fine and needs to be replaced.

To replace the fob battery, begin by prying open the case with a screwdriver or watch-type tool. Be careful not to put too much pressure on the fob because this could cause the fob's to split apart. If the fob isn't opening try prying the tool several times around the outside of case.

After the fob has been opened, remove the mechanical key and open the electronic portion of the car. Insert the new battery and snap it back into the shell. If the key fob doesn't work after this, there may be a more serious problem with your car's remote start system that requires a professional diagnostic. A reputable mechanic will be capable of helping you if this is the situation. If you require assistance with your vehicle, you can contact roadside assistance.

Broken Key Ring

There are a few options to do in the event that your key fob won't work because the ring is broken. Look to see if can locate the broken piece inside the ignition. If it's still in there the ignition, take it out without causing damage to the ignition lock or the door lock. Call a locksmith if you have difficulty removing the key. They have tools that can safely remove a broken car key repair near me key from the ignition.

A broken car key could also be the result of corrosion of the plastic frame or circuit board. You can clean the circuit board by using a cotton swab with ruby alcohol. This will remove corrosion and ensure the contact pads aren't damaged.

Repair a damaged rings by using a thick wire or nail to close the hole. You can also use superglue to repair a damaged ring. First, Repair Car Keys clean the damaged ring with a damp cloth and then apply a small amount superglue on each end of the nail or wire. Apply the glue to the ring and let them dry before using your car. These DIY solutions might seem appealing, but they're really just an interim measure. It is recommended to hire an experienced locksmith for long-term repairs. They have the tools and know-how to fix a broken car key quickly and efficiently. They can replace the battery and reprogram the key repair fob, if needed.

Broken Key Blade

Some key blades can break due to a lot of wear and tear. If this happens, it's probably time to buy a new key. This problem isn't nearly as serious as you think at first. The primary problem is that the blade has separated from the case.

Spraying lubricant into the keyhole is a method to repair it. Then you can use pliers, tweezers, or a pin to grab the broken end of the key and take it out. If the key is magnetic, you can also use a magnet to assist in pulling it out. Use a magnet to assist you remove the key, but be cautious to not sever the lock tumbler.

Contact a locksmith immediately in the event that you are unable to take out the damaged part of the key. They're equipped with special tools that can safely remove keys without causing damage.

Super glue can be used to fix an open lock that has snapped. Apply a small amount of glue to the edges of the crack and press them together. Wait until the glue dries before inserting your key into the lock. This method isn't extremely reliable, and you may have to repeat it a few times before it is successful. Super glue might not be able to hold the key together. This is more of a temporary measure rather than an option that can last.

Broken Plastic Loop

If the loop of plastic on your key fob fails it could make the key ineffective. This is a relatively easy fix. You can make use of wire or a finishing nail to replace it. Drill two holes in the broken plastic loop at each end of the nail or wire. Cut the wire or nail to the desired width, and place a small drop of superglue in each hole. Then, press the wire or nail into the holes to seal them and allow it to dry.

Another option is to get an alternative shell from a locksmith who sells them. They can transfer the programmable section of your key into the new shell and cut an entirely new blade at only a fraction of the price.

It's not the most ideal solution, but it can help you get back on the road in case your key broke in half. It's not easy to repair when the blade of the key is in the ignition, however. If you're not careful, you can make use of a hair clip or needle to remove the broken piece from the ignition. Get a locksmith equipped with special tools to safely remove damaged keys from ignitions. You can also request a new key made with the proper cuts for the ignition of your car.

Broken Master Key

If a key breaks inside the lock, you'll have to attempt to retrieve it before it is completely destroyed. You can use lubricants, tweezers, and needle nose pliers to grasp the fragment of a broken key.

To start, spray the inside of your lock with a lubricant such as WD-40 or graphite powder. You can also try the hacksaw blade technique, which involves moving the blade along the sides of the broken key, and then grasping a few of its teeth. If you're successful then you should be able to remove the broken key.

Another useful tool is a spiral key extractor that is available in a wide range of hardware stores. It is a thin, flexible bar with spiral threads which can be put into the keyway and bent to get into the broken part of the key. Once it has hooked onto the serrations, you can turn it in a circular direction and press it against the broken section of the key to pull it out.

Before calling a locksmith, try to get rid of the broken master key. If you are unable to get rid of the broken piece it's time to call a locksmith. A locksmith can give you a new key that can be programmed to the transponder of your car.