Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. As opposed to aluminium and timber they don't corrosion or rot.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will prevent unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause severe damage to your home and even be fatal. It is important to take the time to ensure that you are doing everything you can to keep your windows in good condition.

For single pane windows, it can be relatively simple to replace them, and the replacement will generally fit within the old frame very easily. If you have double-paned windows which are joined by internal beading, it is more difficult to remove and replace the old panes. In this situation it is essential to buy plastic spacers to make sure that the new pane fits into the window frame.

If you're planning to try to remove the window panes yourself it is important to wear the appropriate safety equipment, including thick gloves and protective eyewear. You should also lay down a dropcloth before you begin working on the window panes, so that any shards fall onto the fabric and not on the floor and could be trampled under.

After the glass has been removed, it's a good idea to seal the gap with packaging tape or duct tape to prevent drafts and water from entering the home until a professional can come out and repair the window. This also serves as an obstacle to stop criminals from getting into your home. If the gap is large, you may think about an alarm door that comes with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time they may be afflicted by a variety of issues, including sagging. A sagging window in uPVC could cause issues with light, draughts and even security. It is crucial to act when you notice your uPVC windows are sliding.

To repair a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll have to open the window to access the frame. Then, using the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to test the fit after you have repositioned your hinges. If you are happy with the fit of the window, tighten the screws to secure them in the right position.

If you are unable to reposition the hinges, you may need to replace the seal. Over time rubber seals can lose their elasticity and become dry, which causes their tightness to decrease. It is essential to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

UPVC handles can also loosen up. Often this is due to screws that have become loose over time. However, it can occur because the handle mechanism has worn out. It's a good thing that it's simple to fix a loose uPVC window handle yourself. First, you'll need to close your window and do a test fit. The corner joints of the sash need to be aligned with the casing joint. If it does not then you can use the screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

It is essential to act if you awake each day to find mouldy walls and wet floors. The leaks of water from windows do not only lead to the degrading of the structure of your home but also undermine your efforts to control the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a relatively easy fix that can be done by any skilled DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer can be put on. When it comes to uPVC repair, you should avoid 'over-caulking'. This will make your window harder to clean and reduce its energy efficiency.

Check that any drainage holes are free of debris inside them and that the sill pan has been angled correctly to drain away from the window. In more serious cases you might need to consider replacing the window.

Mold spots and rotten sills are also signs of water leakage. This fungus thrives under humid conditions and can propagate quickly throughout the house.

If the leakage is occurring between the double-glazed glass it is more likely that the issue is more with the seal rather than the frame. It is also possible to be corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open with a breeze It could be the hinges that are at fault. These are easily repaired by any skilled DIYer and are usually completed in just a few minutes.

Almost every household in the UK will have either top hung or side hung uPVC windows that are hinged and like any mechanical part they can wear down over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier to do when you have a person to help you hold the frame up.

It is also important to verify that the uPVC hinges are opened and closed in the right direction. You can do this by checking for the arrows on each hinge. This indicates which way the window repair should open.

The problem with the hinges on windows could be caused by improperly opening the window a certain way or due to poor installation at the factory. Sending us photos via our website is often enough to solve the issue. We are happy to give advice.

Regularly lubricating the hinges is essential. This can be accomplished by applying an oil that is light in nature to the hinges. We recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window operate and close more smoothly. It can also lower the possibility of a window getting stuck and stop corrosion. The ideal time to do this once a year. WD40 or other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by several different causes. The hinges can also become disaligned as a result of wear, which can cause gaps between the frame and sash. These can be easily repaired by giving them good cleaning, but in the event that they are beyond repair timber windows it could be necessary to have them aligned or replaced. Secondly the interlock, this is on the hinge side of the window, can be misaligned. Again, it may be possible to just give them a thorough clean, however in certain cases, it may be necessary to have these replaced.

These seals can wear down or get damaged over time, allowing air escape. Installing high-quality weatherstripping will help to stop draughts. Another option is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures, and also lessen draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are usually made of fabric tubes filled with a filler, which can be hung over your window sill. They can keep your home warm by blocking out cold air.

Your windows made of upvc will continue to provide excellent insulation and security to your home by performing regular maintenance and repairs. It is crucial to keep in mind that all windows will eventually become worn out, repairs to double glazing and it is cheaper to replace them than to repair them. If you have any problems with your window glass repair near me made of upvc, it's best to consult an expert as soon as possible.