double glazed patio door repairs Door Lock Repairs

Over time, the wear and tear can lead to lock malfunctions. There are a few basic steps you can follow to restore the security of your uPVC door.

These quick fixes can make your home safer no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Patio doors are great for letting the outdoors in while keeping the elements out. However they could pose an issue for security when the lock isn't functioning properly. As time passes, wear and tear, hot and cold weather, dirt and debris can cause damage to your patio door's lock and cause it to become difficult to open. With a little care you can make sure that your patio door's locks always function effectively.

It's important to first clean the patio door lock as well as all moving parts. This helps to remove any dirt and coatings that may hinder the lock from functioning in the way it should. Start by wiping down the moving parts of the lock for your local Patio door Repairs door with a damp cloth, then employ a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door and frame that are ingrained with dirt. It is recommended to wipe the entire lock using dry cloth to get rid of any remaining dampness and allow it to air dry before applying it to the next time.

If you have an outdoor door that has a pin tumbler latch mechanism You can grease the lock by applying graphite powdered to the key or by using an lubricant based on Teflon like WD-40 Multi-Use. This type of lubricant can be easy to apply and it won't disintegrate with time. If you are unable to find the right lubricant for your needs, you could try using a pencil that has an extremely thick tip. Place the pencil in the lock and move it around a bit to spread the graphite.

Regular maintenance is also required to keep the tracks of sliding patio doors clear from dust, dirt and other debris. They are particularly susceptible to snow, ice, and other debris that could cause them to block or become stuck. This could make it difficult for your patio door to open and shut.

You can clean the track rails and rollers of sliding patio door repair patio doors by removing damaged or dirty weather stripping. Clean it, then replace it. Patio door rollers can also be cleaned and sprayed with an oil that is non-stick.

Lubricate the Moving Parts

uPVC french doors, similar to sliding patio doors, operate using 3-4 or sometimes five-point locking mechanisms, which include the handle and lock cylinder operated by a key. These doors require maintenance, lubrication of the moving parts. This can be done using a thin oil (never WD40) and should be done once per year.

If hinges that are sagging don't cause the problem it could be because the door is misaligned. It could be rubbing against or catching the hole of the strike plate in the frame. The solution is to remove the strike plate and use a sharp chisel to enlarge the mortise that it rests in. This will permit the latch to fit properly into the hole, and prevent it from hitting the frame.

Find the width of the cylinder with an object of book or wood that fits into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw until the end of the cylinder.

Verify the width of the lock.

If your patio door latch isn't able to turn even after cleaning and lubricating, it's possible that it's not in alignment with the strike plate hole. Check if your door is balanced, and that the hinge screws are tight. In most instances, moving the strike plate upwards or downwards can solve the issue.

The latch may not engage properly in the event that the strike of the lock is too small. In this case, enlarge the hole with a chisel and hammer. Then, test the latch to ensure it doesn't rub against the jamb frame of the door or fall the frame.

Before you purchase a replacement lock, it is important to determine the mortise type of lock you have. This can be done by taking a look at the faceplate of the lock and noting if it is square or round. Examine each screw hole on the existing lock, and note their size. This will enable you to find an alternative lock that is the exact same width and will fit into your existing hole.

You'll need to identify the mortise lock and examine it for any scratches, bends, or other damage that requires to be repaired. A bent or damaged latch is more likely to break than one that hasn't been frequently used, so be sure to replace the lock with a brand new, secure version if you find any signs of wear or damage.

Once you've inspected the lock and decided on the type of replacement you'll need then it's time to begin working on the actual repair. Take the old handle and spindle out of your patio door, and then put in the new one. Begin by installing the handle in the interior, aligning it with the spindle and then securing it in place by using the two screws or bolts which hold it. Once the handle's interior is installed, put in the handle on the outside and screw it into place as well. Once you've completed these steps, you can test the new handles to ensure that they open and close easily and that the latch catches properly with the strike plate.

Check the Strike on the door.

The door latch and strike plate are two parts of the lock that work to ensure that the latch is secure the door. An incorrectly aligned strike plate and door latches can cause the latch to not latch the door in a proper manner. This problem is usually very simple to solve.

Check the receiving holes of the strike plate to ensure they are free of obstructions, such as dirt or plastic plugs. Then loosen the keeper screws that secure the strike plate in place, allowing it to move vertically, but not removing it from the frame of the door. Then, you can adjust the strike plate so that its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted tighten all screws and check whether the door shuts smoothly.

Door strike plates can be a bit difficult to locate for homeowners with sliding patio door lock repair patio doors, however they're crucial to lock and unlock your door. The plates made of metal are located at the top and bottom jambs of the door where they support its latch. The door latch slides into this strike plate and Local patio door repairs creates a seal. If the strike plate has been damaged or rusted, or if it is not installed correctly, the latch may not be able to lock the door properly.

One common reason for a patio door lock to become stuck or not close is a misalignment between the latch and the strike plate. The easiest way to check for this is with the "lipstick test." Apply some lipstick on the outside of the deadbolt, then apply masking tape over it. The lipstick will leave an impression when you shut the door. This will reveal exactly where the latch joins the strike plate. If the mark is too low or high, you can adjust the strike plate.

Locks for sliding patio doors help protect your home from burglars. If they're not working correctly, you should solve the issue fast. By following these easy steps, you'll be able to fix the lock on your patio door and regain its functionality in a matter of minutes.